Volume: 2Date: 2024-01-01Original Date: 2024-01-01Title: PART 97 - STANDARD INSTRUMENT PROCEDURESContext:
Title 14 - Aeronautics and Space. CHAPTER I - FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED). SUBCHAPTER F - AIR TRAFFIC AND GENERAL OPERATING RULES.
Pt. 97PART 97—STANDARD INSTRUMENT PROCEDURESSubpart A—GeneralSec.97.1Applicability.97.3Symbols and terms used in procedures.97.5Bearings, courses, tracks, headings, radials, miles.Subpart B—Procedures97.10[Reserved]Subpart C—TERPS Procedures97.20General.Authority:49 U.S.C. 106(f), 106(g), 40103, 40106, 40113, 40114, 40120, 44502, 44514, 44701, 44719, and 44721-44722.Source:Docket No. 1580, 28 FR 6719, June 29, 1963, unless otherwise noted.Subpart A—General§ 97.1Applicability.(a) This part prescribes standard instrument approach procedures to civil airports in the United States and the weather minimums that apply to landings under IFR at those airports.(b) This part also prescribes obstacle departure procedures (ODPs) for certain civil airports in the United States and the weather minimums that apply to takeoffs under IFR at civil airports in the United States.
[Doc. No. FAA-2002-14002, 72 FR 31679, June 7, 2007]
§ 97.3Symbols and terms used in procedures.As used in the standard instrument procedures prescribed in this part—Aircraft approach category
means a grouping of aircraft based on a speed of VREF, if specified, or if VREF is not specified, 1.3 V
so
at the maximum certificated landing weight. VREF, V
so
, and the maximum certificated landing weight are those values as established for the aircraft by the certification authority of the country of registry. The categories are as follows—
(1) Category A: Speed less than 91 knots.(2) Category B: Speed 91 knots or more but less than 121 knots.(3) Category C: Speed 121 knots or more but less than 141 knots.(4) Category D: Speed 141 knots or more but less than 166 knots.(5) Category E: Speed 166 knots or more.Approach procedure segments
for which altitudes (minimum altitudes, unless otherwise specified) and paths are prescribed in procedures, are as follows—
Code of Federal Regulations /
Title 14 - Aeronautics and Space /
Vol. 2 / 2024-01-01881
(1) Initial approach is the segment between the initial approach fix and the intermediate fix or the point where the aircraft is established on the intermediate course or final approach course.(2) Initial approach altitude is the altitude (or altitudes, in high altitude procedure) prescribed for the initial approach segment of an instrument approach.(3) Intermediate approach is the segment between the intermediate fix or point and the final approach fix.(4) Final approach is the segment between the final approach fix or point and the runway, airport, or missed approach point.(5) Missed approach is the segment between the missed approach point, or point of arrival at decision altitude or decision height (DA/DH), and the missed approach fix at the prescribed altitude.Ceiling
means the minimum ceiling, expressed in feet above the airport elevation, required for takeoff or required for designating an airport as an alternate airport.
Copter procedures
means helicopter procedures, with applicable minimums as prescribed in § 97.35. Helicopters may also use other procedures prescribed in subpart C of this part and may use the Category A minimum descent altitude (MDA), or decision altitude or decision height (DA/DH). For other than “copter-only” approaches, the required visibility minimum for Category I approaches may be reduced to one-half the published visibility minimum for Category A aircraft, but in no case may it be reduced to less than one-quarter mile prevailing visibility, or, if reported, 1,200 feet RVR. Reduction of visibility minima on Category II instrument approach procedures is prohibited.
FAF
means final approach fix.
HAA
means height above airport and is expressed in feet.
HAL
means height above landing and is the height of the DA/MDA above a designated helicopter landing area elevation used for helicopter instrument approach procedures and is expressed in feet.
HAS
means height above the surface and is the height of the DA/MDA above the highest terrain/surface within a 5,200-foot radius of the missed approach point used in helicopter instrument approach procedures and is expressed in feet above ground level (AGL).
HAT
means height above touchdown.
HCH
means helipoint crossing height and is the computed height of the vertical guidance path above the helipoint elevation at the helipoint expressed in feet.
Helipoint
means the aiming point for the final approach course. It is normally the center point of the touchdown and lift-off area (TLOF).
Hold in lieu of PT
means a holding pattern established under applicable FAA criteria, and used in lieu of a procedure turn to execute a course reversal.
MAP
means missed approach point.
More than 65 knots
means an aircraft that has a stalling speed of more than 65 knots (as established in an approved flight manual) at maximum certificated landing weight with full flaps, landing gear extended, and power off.
MSA
means minimum safe altitude, expressed in feet above mean sea level, depicted on an approach chart that provides at least 1,000 feet of obstacle clearance for emergency use within a certain distance from the specified navigation facility or fix.
NA
means not authorized.
NOPT
means no procedure turn required. Altitude prescribed applies only if procedure turn is not executed.
Procedure turn
means the maneuver prescribed when it is necessary to reverse direction to establish the aircraft on an intermediate or final approach course. The outbound course, direction of turn, distance within which the turn must be completed, and minimum altitude are specified in the procedure. However, the point at which the turn may be begun, and the type and rate of turn, is left to the discretion of the pilot.
RA
means radio altimeter setting height.
RVV
means runway visibility value.
SIAP
means standard instrument approach procedure.
65 knots or less
means an aircraft that has a stalling speed of 65 knots or less (as established in an approved flight
manual) at maximum certificated landing weight with full flaps, landing gear extended, and power off.
Code of Federal Regulations /
Title 14 - Aeronautics and Space /
Vol. 2 / 2024-01-01882
T
means nonstandard takeoff minimums or specified departure routes/procedures or both.
TDZ
means touchdown zone.
Visibility minimum
means the minimum visibility specified for approach, landing, or takeoff, expressed in statute miles, or in feet where RVR is reported.
[Doc. No. FAA-2002-14002, 72 FR 31679, June 7, 2007]
§ 97.5Bearings, courses, tracks, headings, radials, miles.(a) All bearings, courses, tracks, headings, and radials in this part are magnetic, unless otherwise designated.(b) RVR values are stated in feet. Other visibility values are stated in statute miles. All other mileages are stated in nautical miles.
[Doc. No. 561, 32 FR 13912, Oct. 6, 1967, as amended by Amdt. 97-1336, 72 FR 31680, June 7, 2007]
Subpart B—ProceduresEditorial Note:
The procedures set forth in this subpart were formerly carried as §§ 609.100 through 609.500 of this title and were transferred to part 97 as §§ 97.11 through 97.19, respectively, but are not carried in the Code of Federal Regulations. For
Federal Register
citations affecting these procedures, see the List of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at
www.govinfo.gov.§ 97.10[Reserved] Subpart C—TERPS ProceduresSource:Docket No. 8130, 32 FR 13912, Oct. 6, 1967, unless otherwise noted.Editorial Note:
The procedures for §§ 97.21 through 97.37, respectively, are not carried in the Code of Federal Regulations. For
Federal Register
citations affecting these procedures, see the List of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at
www.govinfo.gov.§ 97.20General.(a) This subpart prescribes standard instrument approach procedures and takeoff minimums and obstacle departure procedures (ODPs) based on the criteria contained in FAA Order 8260.3, U.S. Standard for Terminal Instrument Procedures (TERPs), and other related Orders in the 8260 series that also address instrument procedure design criteria.
(b) Standard instrument approach procedures and associated supporting data adopted by the FAA are documented on FAA Forms 8260-3, 8260-4, 8260-5. Takeoff minimums and obstacle departure procedures (ODPs) are documented on FAA Form 8260-15A. These forms are incorporated by reference. The Director of the Federal Register approved this incorporation by reference pursuant to 5 U.S.C. 552(a) and 1 CFR part 51. The standard instrument approach procedures and takeoff minimums and obstacle departure procedures (ODPs) are available for examination at the U.S. Department of Transportation, Docket Operations, 1200 New Jersey Avenue SE, West Building Ground Floor, Room W12-140, Washington, DC 20590, and at Aeronautical Information Services, 1305 East-West Highway, Silver Spring, MD 20910, or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email:
fedreg.legal@nara.gov
, or go to
http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
(c) Standard instrument approach procedures and takeoff minimums and obstacle departure procedures (ODPs) are depicted on aeronautical charts published by the FAA. These charts are available from the FAA at
https://www.faa.gov/air_traffic/flight_info/aeronav/digital_products/.
[Doc. No. FAA-2002-14002, 72 FR 31680, June 7, 2007, as amended by Docket FAA-2018-0119, Amdt. 97-1338, 83 FR 9172, Mar. 5, 2018; Docket No. FAA-2022-1355, Amdt. No. 97-1339, 87 FR 75846, Dec. 9, 2022]